|
Service Doors | "Climate Guard" | "Thermal Guard" | Fire Doors | Counter Fire Doors | Aluminum Counter Doors
Steel and Stainless Steel Counter Doors | Special Accessories | Additional Products | DBCi Light Duty Doors
Service and Standard Duty Doors Features:
6" minimum
diameter structural
steel pipe barrel |
Oil tempered torsion springs on continuous cold-rolled steel shaft |
 |
Prime-painted galvanized steel hood |
Steel plate brackets attach to wall angles |
Chain operation with cast iron gears |
Formed steel channel or structural steel angle guides and continous wall angle mounting |
Interlocking prime painted galvanized steel slats |
Double steel angle footpiece with astragal
 |
Extruded aluminum footpiece with astragal
 |
Face of Wall Mount
(channel guide shown)
|
Optional Between-Jamb Mount
 |
Face of Wall Mount
(Optional Angle guide shown)
|
< back to top
"Climate-Guard" Weatherstripped Doors
Climate control is provided by the combination of a flat slat curtain, hood baffle, guide weatherstripping and astragal.
Specifications
Note: Specifications for R & S "Climate-Guard" weatherstripped doors are the same as for service doors with the following substitutions:
Part 2 Products
2.01 Materials
A. Manufacturer: R & S Manufacturing, model W ___
D. Curtain: Interlocking type ___ flat slats are roll formed from galvanized steel coil. Gage of slats is as required to meet windload. Endlocks are riveted to slats to maintain curtain alignment. Windlocks are riveted to slats when required to meet windload. Bottom of curtain is reinforced by an extruded aluminum or double steel angle footpiece with astragal.
E. Guides: Steel channels or structural steel angles form curtain guides and are bolted to structural steel wall angles. Sizes of guides are as required to retain curtain under windload. Windlock bars are provided when winlocks are required to meet windload. Vinyl guide weatherstripping against the flatfaced side of the slats is standard (wool pile, brush, or weatherstripping on both sides of the curtain are optional).
H. Hood: Formed from minimum 24 gage galvanized steel sheet, reinforced with tip and bottom flanges to limit defection. Internal vinyl hood baffle is standard. Intermediate support is provided when required.
Model Designation
By Method of Operation
Face of Wall Mount
WFP - Push-up
WFC - Chain
WFT - Thru-wall-chain
WFA - Awning Crank
WFB - Crank Box
WFM - Motor
< back to top
"Thermal-Guard" Insulated Doors
An effective thermal barrier is created by the combination of 22 gage (min.) steel flat faced slats, 3/4" polyurethane foam, and 24 gage steel back slats.
Specifications
Note: Specifications for R&S "Thermal-Guard" insulated doors are the same as for service doors with the following substitutions:
Part 2 Products
2.01 Materials
A. Manufacturer: R&S Manufacturing, model I ___
D. Curtain: Interlocking type 25 flat slats are roll formed from galvanized steel coil. Gage of slats is as required to meet windload. Polyurethane foam, 3/4" thick, is laid in place for complete coverage and concealed by a 24 gage back slat (22 gage back slat optional). Endlocks are riveted to slats to maintain curtain alignment. Windlocks are riveted to slats when required to meet windload. Bottom of curtain is reinforced by an extruded aluminum or double steel angle footpiece with astragal.
E. Guides: Structural steel angles form curtain guides and are bolted to structural steel wall angles. Sizes of guides are as required to retain curtain under windload. Windlock bars are provided when windlocks are required to meet windload. Vinyl guide weatherstripping against the flat-faced side of the slats is standard (wool pile, brush, or weatherstripping on both sides of the curtain are optional).
H. Hood: Formed from minimum 24 gage galvanized steel sheet, reinforced with top and bottom flanges to limit deflection. Internal vinyl hood baffle is standard. Intermediate support is provided when required.
< back to top
Fire Doors
R&S Fire Doors combine the durability, security, efficiency and space saving advantages of a rolling service door with the added life and property saving benefits of automatic fire protection. Underwriters Laboratories 3-Hour/Class 'A' Label or Oversize Certificate of Compliance is furnished standard.
Specifications
Part 2 Products
2.01 Materials
A. Manufacturing: R&S Manufacturing, model R ___
D. Automatic closing: Thermally activated by 165˚ fusible links, with the closing speed regulated by a governor device operative only during automatic closing.
E. Curtain: Interlocking type ___ slats are roll formed from galvanized steel coil. Gage of slats is as required by the listing. Endlocks are riveted to slats to maintain curtain alignment. Bottom of curtain is reinforced by a double steel angle footpiece.
F. Guides: Steel channels or structural steel angles form curtain guides and are bolted to structural steel wall angles. Sizes of guides are as required by the listing.
I. Hood: Formed from minimum 24 gage galvanized steel sheet, reinforced with top and bottom flanges to limit deflection. A thermally released integral flame baffle is provided when required by the listing.
Options
Smoke Detectors: photoelectric (detects smoke and heat) or ionization (detects combustion particles); require connection to a release device with compatible voltage
Release Devices: Electro-thermal and McCabe links (normally open circuits); electromagnetic and time delay fail-safe releases (normally closed circuits)
Model SS90-C Release Device: provides automatic closing and testing of motor operated fore doors upon activation by a detector or alarm; eliminates the need for mechanical release and reset unless there is a power loss; allows for a cycling sequence of the door in the event an obstruction is encountered upon closing
Perimeter Gasketing: brush seals factory applied to guides and footpiece, field installed on header, to aid in smoke and draft control
Vision Lites: single or multiple 4" wide cutouts, glazed with clear wire glass (11/2 hour rating)
Sloped Footpiece: for special sill conditions
Cylinder Locks: on footpiece
< back to top
Counter Fire Doors
R&S Counter Fire Doors integrate the automatic fire protection of a rolling fire door with the compact design and neat appearance of a counter door. They are available in primed steel or stainless steel and with most of the same options as Fire Doors. Warnock Hersey 1 1/2-Hour Label or Oversize Certificate is furnished standard.
Specifications
Part 2 Products
2.01 Materials
A. Manufacturer: R&S Manufacturing, model L ___ Model SL ___ (for stainless)
D. Automatic closing: Thermally activated by 165˚ fusible links, with the closing speed regulated by a governor device operative only during automatic closing.
E. Curtain: Interlocking type 18 flat slats are roll formed from (galvanized steel) (stainless steel - 12' max. width) coil. Gage of slats is as required by the listing. Endlocks are riveted to slats to maintain curtain alignment. Bottom of curtain is reinforced by a (single angle) (tubular) footpiece of material matching slats.
F. Guides: Box shape guides are formed from (steel) (stainless steel). Sizes of guides are as required by the listing.
I. Hood: Formed from 24 gage (galvanized steel) (stainless steel) sheet, reinforced with tip and bottom flanges to limit deflection. A thermally released integral flame baffle is provided when required by the listing.
2.02 Finish
A. Galvanized steel slats and hoods are pre-finished with a baked on grey polyester primer before forming. Steel footpiece, guides and brackets receive one coat of rust inhibiting grey primer. Exposed stainless steel provided with #4 finish.
Options
Smoke Detectors: photoelectric (detects smoke and heat) or ionization (detects combustion particles): require connection to a release device with compatible voltage
Release Devices: Electro-thermal and McCabe links (normally open circuits); electro-magnetic and time delay failsafe releases (normally closed circuits)
Model SS90-C Release Device: provides automatic closing and testing of motor operated counter fire doors upon activation by a detector or alarm; eliminates the need for mechanical release and reset unless there is a power loss; allows for a cycling sequence of the door in the event an obstruction is encountered upon closing
Perimeter Gasketing: brush seals factory applied to guides and footpiece, field installed on header, to aid in smoke and draft control
Vision Lites: single or multiple 4" wide cut-outs, glazed with clear wire glass (1 1/2 hour rating)
< back to top
Aluminum Counter Doors
R&S Aluminum Counter Doors offer compact design and attractive appearance. Anodized extruded aluminum components combine light weight, a smooth, bright finish and excellent corrosion resistance for a variety of applications. Counter door construction can be modified to provide for anodized aluminum service doors to 12 feet wide, 10 feet high and 100 square feet.
Specifications
Part 2 Products
2.01 Materials
A. Manufacturer: R&S Manufacturing, model S ___
B. Mounting: Face of wall or between-jamb
C. Operation: Push-up is standard (awning crank should be considered when doors are to be operated over a deep counter or over 7' high). Chain hoist or motor operation are optional.
D. Curtain: Interlocking type 15 flat slats are extruded from 6063 alloy aluminum. Endlocks are riveted to slats to maintain curtain alignment. Bottom of curtain is reinforced by an extruded aluminum tubular footpiece with astragal.
E. Guides: Extruded aluminum guides are bolted to aluminum wall angles. Guides are fitted with nylon pile wearstrips.
F. Brackets: Steel plate brackets are bolted to wall angles to support curtain and barrel and provide mounting for hood.
G. Barrel: Steel pipe houses torsion spring assembly and supports curtain with a maximum deflection of .03 inch per foot of width. Torsion springs are mounted on a continuous cold rolled steel shaft, adjustable by a tension wheel outside or inside one bracket.
H. Hood: Formed from aluminum sheet, reinforced with top and bottom flanges to limit deflection.
I. Locking: Slidebolt locks (cylinder locks are optional).
2.02 Finish
A. Aluminum slats, footpiece, guides and hood are clear anodized. Steel brackets receive one coat or rust inhibiting grey primer. (Dark bronze and other color anodized finishes are optional.)
Part 3 Execution
3.01 Installation
A. Counter doors are to be installed by an R & S authorized representative in accordance with R & S installation instructions.
< back to top
Steel and Stainless Steel Counter Doors
R&S Steel and Stainless Steel Doors combine the strength and durability of a rolling service door with compact design and neat appearance. Although primarily utilized as a closure on counter openings, it may also be used on openings providing walk-thru or drive-thru access. Counter doors can provide modified construction for stainless steel service door requirements to 16 feet wide, 10 feet high and 144 square feet.
Specifications
Part 1 General
1.01 Summary
A. Counter doors excluding design, construction and preparation of openings; finish or field painting; access panels; electrical wiring, conduit, wire, fuses and disconnect switches
Part 2 Products
2.01 Materials
A. Manufacturer: R&S Manufacturing, model N ___, model SN ___ (for stainless)
B. Mounting: Face of wall or between-jamb
C. Operation: Push-up to 14' wide and awning crank on larger sizes is standard (awning crank should be considered when doors are to be operated over a deep counter or over 7' high). Chain hoist or motor operation are optional.
D. Curtain: Interlocking type 18 flat slats are roll formed from (galvanized steel) (stainless steel) coil. Endlocks are riveted to slats to maintain curtain alignment. Bottom of curtain is reinforced by a (single angle) (tubular) footpiece of material matching slats, with astragal.
E. Guides: Box shape guides are formed from (steel) (stainless steel).
F. Brackets: Steel plate brackets are bolted to guides to support curtain and barrel and provide mounting for hood.
G. Barrel: Steel pipe houses torsion spring assembly and supports curtain with a maximum deflection of .03 inch per foot of width. Torsion springs are mounted on a continuous cold rolled steel shaft, adjustable by a tension wheel outside or inside one bracket.
H. Hood: Formed from 24 gage (galvanized steel ) (stainless steel) sheet, reinforced with top and bottom flanges to limit deflection.
I. Locking: Slidebolt locks on single angle footpiece and cylinder lock on optional tubular footpiece
2.02 Finish
A. Galvanized steel slats and hoods are pre-finished with a baked on grey polyester primer before forming. Stell footpiece, guides and brackets receive one coat of rust inhibiting grey primer. Exposed stainless steel provided with #4 finish.
Part 3 Execution
3.01 Installation
A. Counter doors are to be installed by an R&S authorized representative in accordance with R & S installation instructions.
< back to top
Special Accessories
Powder Coating Finish
Powder coating is a durable and decorative finish for steel or aluminum surfaces. It provides longer life and requires less maintenance than a standard finish. Powder coating is available in a variety of colors for use on many products. Consult factory for color selection, applications and limitations.
Tubular Motor Operator
Tubular motor operators, completely contained within the barrel, can be provided for counter doors (to 84 sq. ft.) and grilles (to 200 sq. ft.) in limited usage applications. Only the manual crank override is visible outside the bracket. The units are available in 115 volt/single phase with constant contact one button or keyswitch control. They can also be provided with a low voltage controller when options such as a reversing edge or timer are required.
Safety Bearing
This unique safety device functions as both a bearing and inertia brake for motorized service doors and grilles. The safety bearing is designed to prevent the curtain from free-falling if there is damage to or failure of the motor operator, drive chain or spring assembly. If a malfunction occurs and the downward speed increases to an unsafe rate, the inertia brake absorbs the added energy and safely stops the load.
VIBRATECH ®
Viscous speed governor available on R & S Manufacturing, Inc. firedoors for new construction and retro-fit. Viscous speed governor is a patented device allowing for a smooth and quiet descent of firedoors, replaces standard ductile iron governor, and recommended on larger certificate size firedoors, either manual or motorized operation. Viscous speed governor is U.L. listed and conforms to ASTM E152, CAN4-S104, NFPA 252, and UL 10B. Simple, maintenance-free design and construction, with a one year warranty.
< back to top
Additional Products
Side-Folding Closures
An alternative to the traditional rolling grille is provided by folding aluminum panels, either open or glazed, suspended form an overhead track. This design is ideal for very wide or irregular openings requiring curved tracks. They are available as single slide or bi-parting units in a variety of finishes.
Wood Counter Doors
The natural beauty and richness of real wood are combined with the compact design and typical features of a metal counter door. The standard wood for slats, footpiece, guides and hood is red oak. Birch, whit oak, mahogany, pine, fir and other select hardwoods are also available.
Insulated Security Shutters
Compact shutters with PVC or extruded aluminum foam filled slats provide environmental protection for a wide range of applications. They are available in a choice of mounting configurations, methods of operation and color options.
Light Duty Service Doors by DBCi
DBCi is a leading manufacturer of steel curtain roll-up doors and components for the self-storage and commercial door markets.
General Description:
- Designed for frequent usage requirements
- Light duty applications for frequent usage including warehouse, freight terminal and industrial warehouse
- Utilizes 12” drums
- Limited maximum size of 12’ x 18’
Curtain:
- 26-gauge galvanized
- Grade E hard steel
- Deep ribbed corrugation
- 20 standard colors — special colors upon request with upcharge
- Siliconized polyester Weather X paint over prime coat
- Wash coat over primer interior side
- 25-year film integrity warranty — up to 20-year chalk and fade
- Improved flexible wear strips
- 4" of curtain add
Bottom Bar:
- 6063-T6 aluminum extrusion
- 2” x 11/2” galvanized angles
- Bulb astrigal
- Stainless steel nuts and bolts
Axle/Torque Tube:
- 1 5/16” O.D. steel axle, 14-gauge
- Oil tempered torsion springs
- 16-gauge drums 12” diameter galvanized
- Steel ball bearings
- Full top sheet 26-gauge galvanized
Guides:
- 14-gauge galvanized
- Polyethylene wear strip
- Bolt on head stop 1/4” plate steel
- 15/8” deep engagement
- Pre punched for lock and attachment screws
Hardware:
- 13-gauge saddle clamps
- 10-gauge slide locks 2 per door
- 16-gauge step plate 2 per door
- 1/4” steel welded angle T-bracket
Options:
- Insulation Series 2250
- Chain hoist 4:1 reduction
- Vision panels (17” x 5”)
- Top draft stop
- Hood
- Steel mounting plates
- Electric operator
< back to top
|
